wangyan/CCU621M
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Initial commit: CCU621_M firmware project with BLE debug link support.

Browse Source 
Co-authored-by: Cursor <cursoragent@cursor.com>
This commit is contained in:
jiankalka
2026-07-08 17:28:36 +08:00
commit 9ceb218f80
1597 changed files with 724159 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files
Drivers/CMSIS/GD/GD32H7xx/Source/system_gd32h7xx.c
+891
View File
@@ -0,0 +1,891 @@
/*!
\file system_gd32h7xx.c
\brief CMSIS Cortex-M7 Device Peripheral Access Layer Source File for
gd32h7xx Device Series
*/
/*
* Copyright (c) 2009-2021 Arm Limited. All rights reserved.
* Copyright (c) 2025, GigaDevice Semiconductor Inc.
*
* SPDX-License-Identifier: Apache-2.0
*
* Licensed under the Apache License, Version 2.0 (the License); you may
* not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an AS IS BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/* This file refers the CMSIS standard, some adjustments are made according to GigaDevice chips */
#include "gd32h7xx.h"
/* system frequency define */
#define __IRC64M (IRC64M_VALUE) /* internal 64 MHz RC oscillator frequency */
#define __HXTAL (HXTAL_VALUE) /* high speed crystal oscillator frequency */
#define __LPIRC4M (LPIRC4M_VALUE) /* low power internal 4 MHz RC oscillator frequency */
#define __SYS_OSC_CLK (__IRC64M) /* main oscillator frequency */
#define VECT_TAB_OFFSET (uint32_t)0x00 /* vector table base offset */
#define RCU_APB4EN_SYSCFG (uint32_t)0x01 /* enable SYSCFG clk */
/* select a system clock by uncommenting the following line */
/* use IRC64M */
//#define __SYSTEM_CLOCK_IRC64M (__IRC64M)
//#define __SYSTEM_CLOCK_480M_PLL0_IRC64M (uint32_t)(480000000)
//#define __SYSTEM_CLOCK_600M_PLL0_IRC64M (uint32_t)(600000000)
/* use LPIRC4M */
//#define __SYSTEM_CLOCK_LPIRC4M (__LPIRC4M)
/* use HXTAL(CK_HXTAL = 25M) */
//#define __SYSTEM_CLOCK_HXTAL (__HXTAL)
//#define __SYSTEM_CLOCK_200M_PLL0_HXTAL (uint32_t)(200000000)
//#define __SYSTEM_CLOCK_400M_PLL0_HXTAL (uint32_t)(400000000)
//#define __SYSTEM_CLOCK_480M_PLL0_HXTAL (uint32_t)(480000000)
#define __SYSTEM_CLOCK_600M_PLL0_HXTAL (uint32_t)(600000000)
/*
Note: the power mode need to match the mcu selection and external power supply circuit.
for iar project:
for 100-pin mcu, need to define macro GD32H7XXV.
for 144-pin mcu, need to define macro GD32H7XXZ.
for 176-pin mcu, need to define macro GD32H7XXI.
for keil project:
do not need to define these macros extra.
according to the selected mcu and external power supply circuit to uncomment
the following macro SEL_PMU_SMPS_MODE.
*/
#if defined(GD32H7XXI)
//#define SEL_PMU_SMPS_MODE PMU_LDO_SUPPLY
//#define SEL_PMU_SMPS_MODE PMU_DIRECT_SMPS_SUPPLY
#define SEL_PMU_SMPS_MODE PMU_BYPASS //电源模式应选为旁路模式，直接使用外部电源供电 lyn
#elif defined(GD32H7XXZ) | defined(GD32H7XXV)
//#define SEL_PMU_SMPS_MODE PMU_LDO_SUPPLY
//#define SEL_PMU_SMPS_MODE PMU_BYPASS
#endif
#define SEL_IRC64MDIV 0x00U
#define SEL_HXTAL 0x01U
#define SEL_LPIRC4M 0x02U
#define SEL_PLL0P 0x03U
#define PLL0PSC_REG_OFFSET 0U
#define PLL0N_REG_OFFSET 6U
#define PLL0P_REG_OFFSET 16U
#define PLL0Q_REG_OFFSET 0U
#define PLL0R_REG_OFFSET 24U
/* set the system clock frequency and declare the system clock configuration function */
#ifdef __SYSTEM_CLOCK_IRC64M
uint32_t SystemCoreClock = __SYSTEM_CLOCK_IRC64M;
static void system_clock_64m_irc64m(void);
#elif defined (__SYSTEM_CLOCK_480M_PLL0_IRC64M)
#define PLL0PSC 16U
#define PLL0N (120U - 1U)
#define PLL0P (1U - 1U)
#define PLL0Q (2U - 1U)
#define PLL0R (2U - 1U)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_480M_PLL0_IRC64M;
static void system_clock_480m_irc64m(void);
#elif defined (__SYSTEM_CLOCK_600M_PLL0_IRC64M)
#define PLL0PSC 16U
#define PLL0N (150U - 1U)
#define PLL0P (1U - 1U)
#define PLL0Q (2U - 1U)
#define PLL0R (2U - 1U)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_600M_PLL0_IRC64M;
static void system_clock_600m_irc64m(void);
#elif defined (__SYSTEM_CLOCK_LPIRC4M)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_LPIRC4M;
static void system_clock_4m_lpirc4m(void);
#elif defined (__SYSTEM_CLOCK_HXTAL)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_HXTAL;
static void system_clock_hxtal(void);
#elif defined (__SYSTEM_CLOCK_200M_PLL0_HXTAL)
#define PLL0PSC 5U
#define PLL0N (40U - 1U)
#define PLL0P (1U - 1U)
#define PLL0Q (2U - 1U)
#define PLL0R (2U - 1U)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_200M_PLL0_HXTAL;
static void system_clock_200m_hxtal(void);
#elif defined (__SYSTEM_CLOCK_400M_PLL0_HXTAL)
#define PLL0PSC 5U
#define PLL0N (80U - 1U)
#define PLL0P (1U - 1U)
#define PLL0Q (2U - 1U)
#define PLL0R (2U - 1U)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_400M_PLL0_HXTAL;
static void system_clock_400m_hxtal(void);
#elif defined (__SYSTEM_CLOCK_480M_PLL0_HXTAL)
#define PLL0PSC 5U
#define PLL0N (96U - 1U)
#define PLL0P (1U - 1U)
#define PLL0Q (2U - 1U)
#define PLL0R (2U - 1U)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_480M_PLL0_HXTAL;
static void system_clock_480m_hxtal(void);
#elif defined (__SYSTEM_CLOCK_600M_PLL0_HXTAL)
#define PLL0PSC 5U
#define PLL0N (120U - 1U)
#define PLL0P (1U - 1U)
#define PLL0Q (2U - 1U)
#define PLL0R (2U - 1U)
uint32_t SystemCoreClock = __SYSTEM_CLOCK_600M_PLL0_HXTAL;
static void system_clock_600m_hxtal(void);
#endif /* __SYSTEM_CLOCK_IRC64M */
/* configure the system clock */
static void system_clock_config(void);
/*!
\brief setup the microcontroller system, initialize the system
\param[in] none
\param[out] none
\retval none
*/
void SystemInit(void)
{
/* FPU settings */
#if (__FPU_PRESENT == 1) && (__FPU_USED == 1U)
/* set CP10 and CP11 Full Access */
SCB->CPACR |= (uint32_t)((0x03U << 10U * 2U) | (0x03U << 11U * 2U));
#endif
SCB_EnableDCache();
SCB_DisableDCache();
/* enable IRC64M */
RCU_CTL |= RCU_CTL_IRC64MEN;
while(0U == (RCU_CTL & RCU_CTL_IRC64MSTB)) {
}
/* no TCM wait state */
RCU_APB4EN |= RCU_APB4EN_SYSCFG;
SYSCFG_SRAMCFG1 &= ~SYSCFG_SRAMCFG1_TCM_WAITSTATE;
RCU_CFG0 &= ~RCU_CFG0_SCS;
/* reset RCU */
/* reset HXTALEN, CKMEN, PLL0EN, PLL1EN, PLL2EN, PLLUSB0 and PLLUSB1 bits */
RCU_CTL &= ~(RCU_CTL_HXTALEN | RCU_CTL_CKMEN | RCU_CTL_PLL0EN | RCU_CTL_PLL1EN | RCU_CTL_PLL2EN | RCU_CTL_HXTALBPS);
RCU_ADDCTL1 &= ~(RCU_ADDCTL1_PLLUSBHS0EN | RCU_ADDCTL1_PLLUSBHS1EN | RCU_ADDCTL1_LPIRC4MEN);
/* reset CFG0, CFG1, CFG2, CFG3 registers */
RCU_CFG0 &= ~(RCU_CFG0_APB1PSC | RCU_CFG0_APB2PSC | RCU_CFG0_APB3PSC | RCU_CFG0_APB4PSC | RCU_CFG0_AHBPSC |
RCU_CFG0_I2C0SEL | RCU_CFG0_SCS | RCU_CFG0_RTCDIV);
RCU_CFG1 &= ~(RCU_CFG1_HPDFSEL | RCU_CFG1_TIMERSEL | RCU_CFG1_PERSEL |
RCU_CFG1_RSPDIFSEL | RCU_CFG1_USART0SEL | RCU_CFG1_USART1SEL | RCU_CFG1_USART2SEL | RCU_CFG1_USART5SEL | RCU_CFG1_PLL2RDIV);
RCU_CFG2 &= ~(RCU_CFG2_SAI2B1SEL | RCU_CFG2_SAI2B0SEL | RCU_CFG2_SAI1SEL | RCU_CFG2_SAI0SEL |
RCU_CFG2_CKOUT0SEL | RCU_CFG2_CKOUT1SEL | RCU_CFG2_CKOUT0DIV | RCU_CFG2_CKOUT1DIV);
RCU_CFG3 &= ~(RCU_CFG3_ADC01SEL | RCU_CFG3_ADC2SEL | RCU_CFG3_SDIO1SEL
| RCU_CFG3_I2C3SEL | RCU_CFG3_I2C2SEL | RCU_CFG3_I2C1SEL);
RCU_CFG4 &= ~(RCU_CFG4_EXMCSEL | RCU_CFG4_SDIO0SEL);
RCU_CFG5 &= ~(RCU_CFG5_SPI0SEL | RCU_CFG5_SPI1SEL | RCU_CFG5_SPI2SEL |
RCU_CFG5_SPI3SEL | RCU_CFG5_SPI4SEL | RCU_CFG5_SPI5SEL);
/* disable all interrupts */
RCU_INT = 0x14FF0000U;
RCU_ADDINT = 0x00700000U;
/* reset all PLL0 parameter */
RCU_PLL0 = 0x01002020U;
RCU_PLL1 = 0x01012020U;
RCU_PLL2 = 0x01012020U;
RCU_PLLALL = 0x00000000U;
RCU_PLLADDCTL = 0x00010101U;
RCU_PLLUSBCFG = 0x00000000U;
RCU_PLL0FRA = 0x00000000U;
RCU_PLL1FRA = 0x00000000U;
RCU_PLL2FRA = 0x00000000U;
#if defined (SEL_PMU_SMPS_MODE)
/* power supply config */
pmu_smps_ldo_supply_config(SEL_PMU_SMPS_MODE);
#endif
/* configure system clock */
system_clock_config();
#ifdef VECT_TAB_SRAM
nvic_vector_table_set(NVIC_VECTTAB_RAM, VECT_TAB_OFFSET);
#else
nvic_vector_table_set(NVIC_VECTTAB_FLASH, VECT_TAB_OFFSET);
#endif
}
/*!
\brief configure the system clock
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_config(void)
{
#ifdef __SYSTEM_CLOCK_IRC64M
system_clock_64m_irc64m();
#elif defined (__SYSTEM_CLOCK_480M_PLL0_IRC64M)
system_clock_480m_irc64m();
#elif defined (__SYSTEM_CLOCK_600M_PLL0_IRC64M)
system_clock_600m_irc64m();
#elif defined (__SYSTEM_CLOCK_LPIRC4M)
system_clock_4m_lpirc4m();
#elif defined (__SYSTEM_CLOCK_HXTAL)
system_clock_hxtal();
#elif defined (__SYSTEM_CLOCK_200M_PLL0_HXTAL)
system_clock_200m_hxtal();
#elif defined (__SYSTEM_CLOCK_400M_PLL0_HXTAL)
system_clock_400m_hxtal();
#elif defined (__SYSTEM_CLOCK_480M_PLL0_HXTAL)
system_clock_480m_hxtal();
#elif defined (__SYSTEM_CLOCK_600M_PLL0_HXTAL)
system_clock_600m_hxtal();
#endif /* __SYSTEM_CLOCK_IRC64M */
}
#ifdef __SYSTEM_CLOCK_IRC64M
/*!
\brief configure the system clock to 64M by IRC64M
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_64m_irc64m(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable IRC64M */
RCU_CTL |= RCU_CTL_IRC64MEN;
/* wait until IRC64M is stable or the startup time is longer than IRC64M_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_IRC64MSTB);
} while((0U == stab_flag) && (IRC64M_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_IRC64MSTB)) {
while(1) {
}
}
/* AHB = SYSCLK / 1 */
RCU_CFG0 |= RCU_AHB_CKSYS_DIV1;
/* APB4 = AHB / 1 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV1;
/* APB3 = AHB / 1 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV1;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 1 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV1;
/* configure IRC64M div */
RCU_ADDCTL1 &= ~(RCU_ADDCTL1_IRC64MDIV);
RCU_ADDCTL1 |= RCU_IRC64M_DIV1;
/* select IRC64M as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_IRC64MDIV;
/* wait until IRC64M is selected as system clock */
while(RCU_SCSS_IRC64MDIV != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_480M_PLL0_IRC64M)
/*!
\brief configure the system clock to 480M by PLL0 which selects IRC64M as its clock source
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_480m_irc64m(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable IRC64M */
RCU_CTL |= RCU_CTL_IRC64MEN;
/* wait until IRC64M is stable or the startup time is longer than IRC64M_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_IRC64MSTB);
} while((0U == stab_flag) && (IRC64M_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_IRC64MSTB)) {
while(1) {
}
}
/* insert TCM wait state at 480MHz */
RCU_APB4EN |= RCU_APB4EN_SYSCFG;
SYSCFG_SRAMCFG1 |= SYSCFG_SRAMCFG1_TCM_WAITSTATE;
/* IRC64M is already stable */
/* AHB = SYSCLK / 2 */
RCU_CFG0 |= RCU_AHB_CKSYS_DIV2;
/* APB4 = AHB / 2 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV2;
/* APB3 = AHB / 2 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV2;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 2 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV2;
/* PLL0 select IRC64MDIV, config IRC64MDIV as IRC64M, PLL0 input and output range */
RCU_ADDCTL1 &= ~(RCU_ADDCTL1_IRC64MDIV);
RCU_ADDCTL1 |= RCU_IRC64M_DIV1;
RCU_PLLALL &= ~(RCU_PLLALL_PLLSEL | RCU_PLLALL_PLL0VCOSEL | RCU_PLLALL_PLL0RNG);
RCU_PLLALL |= (RCU_PLLSRC_IRC64MDIV | RCU_PLL0RNG_4M_8M);
/* PLL0P = IRC64MDIV / 16 * 120 / 1 = 480 MHz */
RCU_PLL0 &= ~(RCU_PLL0_PLL0N | RCU_PLL0_PLL0PSC | RCU_PLL0_PLL0P | RCU_PLL0_PLL0R | RCU_PLL0_PLLSTBSRC);
RCU_PLL0 |= ((PLL0N << PLL0N_REG_OFFSET) | (PLL0PSC << PLL0PSC_REG_OFFSET) | (PLL0P << PLL0P_REG_OFFSET) | (PLL0R << PLL0R_REG_OFFSET));
RCU_PLLADDCTL &= ~(RCU_PLLADDCTL_PLL0Q);
RCU_PLLADDCTL |= (PLL0Q << PLL0Q_REG_OFFSET);
/* enable PLL0P, PLL0Q, PLL0R */
RCU_PLLADDCTL |= RCU_PLLADDCTL_PLL0PEN | RCU_PLLADDCTL_PLL0QEN | RCU_PLLADDCTL_PLL0REN;
/* enable PLL0 */
RCU_CTL |= RCU_CTL_PLL0EN;
/* wait until PLL0 is stable */
while(0U == (RCU_CTL & RCU_CTL_PLL0STB)) {
}
/* select PLL0 as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_PLL0P;
/* wait until PLL0 is selected as system clock */
while(RCU_SCSS_PLL0P != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_600M_PLL0_IRC64M)
/*!
\brief configure the system clock to 600M by PLL0 which selects IRC64M as its clock source
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_600m_irc64m(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable IRC64M */
RCU_CTL |= RCU_CTL_IRC64MEN;
/* wait until IRC64M is stable or the startup time is longer than IRC64M_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_IRC64MSTB);
} while((0U == stab_flag) && (IRC64M_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_IRC64MSTB)) {
while(1) {
}
}
/* insert TCM wait state at 600MHz */
RCU_APB4EN |= RCU_APB4EN_SYSCFG;
SYSCFG_SRAMCFG1 |= SYSCFG_SRAMCFG1_TCM_WAITSTATE;
/* IRC64M is already stable */
/* AHB = SYSCLK / 2 */
RCU_CFG0 |= RCU_AHB_CKSYS_DIV2;
/* APB4 = AHB / 2 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV2;
/* APB3 = AHB / 2 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV2;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 2 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV2;
/* PLL0 select IRC64MDIV, config IRC64MDIV as IRC64M, PLL0 input and output range */
RCU_ADDCTL1 &= ~(RCU_ADDCTL1_IRC64MDIV);
RCU_ADDCTL1 |= RCU_IRC64M_DIV1;
RCU_PLLALL &= ~(RCU_PLLALL_PLLSEL | RCU_PLLALL_PLL0VCOSEL | RCU_PLLALL_PLL0RNG);
RCU_PLLALL |= (RCU_PLLSRC_IRC64MDIV | RCU_PLL0RNG_4M_8M);
/* PLL0P = IRC64MDIV / 16 * 150 / 1 = 600 MHz */
RCU_PLL0 &= ~(RCU_PLL0_PLL0N | RCU_PLL0_PLL0PSC | RCU_PLL0_PLL0P | RCU_PLL0_PLL0R | RCU_PLL0_PLLSTBSRC);
RCU_PLL0 |= ((PLL0N << PLL0N_REG_OFFSET) | (PLL0PSC << PLL0PSC_REG_OFFSET) | (PLL0P << PLL0P_REG_OFFSET) | (PLL0R << PLL0R_REG_OFFSET));
RCU_PLLADDCTL &= ~(RCU_PLLADDCTL_PLL0Q);
RCU_PLLADDCTL |= (PLL0Q << PLL0Q_REG_OFFSET);
/* enable PLL0P, PLL0Q, PLL0R */
RCU_PLLADDCTL |= RCU_PLLADDCTL_PLL0PEN | RCU_PLLADDCTL_PLL0QEN | RCU_PLLADDCTL_PLL0REN;
/* enable PLL0 */
RCU_CTL |= RCU_CTL_PLL0EN;
/* wait until PLL0 is stable */
while(0U == (RCU_CTL & RCU_CTL_PLL0STB)) {
}
/* select PLL0 as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_PLL0P;
/* wait until PLL0 is selected as system clock */
while(RCU_SCSS_PLL0P != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_LPIRC4M)
/*!
\brief configure the system clock to LPIRC4M
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_4m_lpirc4m(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable LPIRC4M */
RCU_ADDCTL1 |= RCU_ADDCTL1_LPIRC4MEN;
/* wait until LPIRC4M is stable or the startup time is longer than LPIRC4M_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_ADDCTL1 & RCU_ADDCTL1_LPIRC4MSTB);
} while((0U == stab_flag) && (LPIRC4M_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_ADDCTL1 & RCU_ADDCTL1_LPIRC4MSTB)) {
while(1) {
}
}
/* LPIRC4M is stable */
/* AHB = SYSCLK / 1*/
RCU_CFG0 |= RCU_AHB_CKSYS_DIV1;
/* APB4 = AHB / 1 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV1;
/* APB3 = AHB / 1 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV1;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 1 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV1;
/* select LPIRC4M as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_LPIRC4M;
/* wait until LPIRC4M is selected as system clock */
while(RCU_SCSS_LPIRC4M != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_HXTAL)
/*!
\brief configure the system clock to HXTAL
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_hxtal(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable HXTAL */
RCU_CTL |= RCU_CTL_HXTALEN;
/* wait until HXTAL is stable or the startup time is longer than HXTAL_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_HXTALSTB);
} while((0U == stab_flag) && (HXTAL_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_HXTALSTB)) {
while(1) {
}
}
/* HXTAL is stable */
/* AHB = SYSCLK / 1*/
RCU_CFG0 |= RCU_AHB_CKSYS_DIV1;
/* APB4 = AHB / 1 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV1;
/* APB3 = AHB / 1 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV1;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 1 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV1;
/* select HXTAL as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_HXTAL;
/* wait until HXTAL is selected as system clock */
while(RCU_SCSS_HXTAL != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_200M_PLL0_HXTAL)
/*!
\brief configure the system clock to 200M by PLL0 which selects HXTAL as its clock source
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_200m_hxtal(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable HXTAL */
RCU_CTL |= RCU_CTL_HXTALEN;
/* wait until HXTAL is stable or the startup time is longer than HXTAL_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_HXTALSTB);
} while((0U == stab_flag) && (HXTAL_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_HXTALSTB)) {
while(1) {
}
}
/* HXTAL is stable */
/* AHB = SYSCLK / 1 */
RCU_CFG0 |= RCU_AHB_CKSYS_DIV1;
/* APB4 = AHB / 2 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV2;
/* APB3 = AHB / 2 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV2;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 2 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV2;
/* PLL0 select HXTAL, configure PLL0 input and output range */
RCU_PLLALL &= ~(RCU_PLLALL_PLLSEL | RCU_PLLALL_PLL0VCOSEL | RCU_PLLALL_PLL0RNG);
RCU_PLLALL |= (RCU_PLLSRC_HXTAL | RCU_PLLALL_PLL0VCOSEL | RCU_PLL0RNG_4M_8M);
/* PLL0P = HXTAL / 5 * 40 = 200 MHz */
RCU_PLL0 &= ~(RCU_PLL0_PLL0N | RCU_PLL0_PLL0PSC | RCU_PLL0_PLL0P | RCU_PLL0_PLL0R | RCU_PLL0_PLLSTBSRC);
RCU_PLL0 |= ((PLL0N << PLL0N_REG_OFFSET) | (PLL0PSC << PLL0PSC_REG_OFFSET) | (PLL0P << PLL0P_REG_OFFSET) | (PLL0R << PLL0R_REG_OFFSET));
RCU_PLLADDCTL &= ~(RCU_PLLADDCTL_PLL0Q);
RCU_PLLADDCTL |= (PLL0Q << PLL0Q_REG_OFFSET);
/* enable PLL0P, PLL0Q, PLL0R */
RCU_PLLADDCTL |= RCU_PLLADDCTL_PLL0PEN | RCU_PLLADDCTL_PLL0QEN | RCU_PLLADDCTL_PLL0REN;
/* enable PLL0 */
RCU_CTL |= RCU_CTL_PLL0EN;
/* wait until PLL0 is stable */
while(0U == (RCU_CTL & RCU_CTL_PLL0STB)) {
}
/* select PLL0 as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_PLL0P;
/* wait until PLL0 is selected as system clock */
while(RCU_SCSS_PLL0P != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_400M_PLL0_HXTAL)
/*!
\brief configure the system clock to 400M by PLL0 which selects HXTAL as its clock source
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_400m_hxtal(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable HXTAL */
RCU_CTL |= RCU_CTL_HXTALEN;
/* wait until HXTAL is stable or the startup time is longer than HXTAL_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_HXTALSTB);
} while((0U == stab_flag) && (HXTAL_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_HXTALSTB)) {
while(1) {
}
}
/* insert TCM wait state at 400MHz */
RCU_APB4EN |= RCU_APB4EN_SYSCFG;
SYSCFG_SRAMCFG1 |= SYSCFG_SRAMCFG1_TCM_WAITSTATE;
/* HXTAL is stable */
/* AHB = SYSCLK / 1 */
RCU_CFG0 |= RCU_AHB_CKSYS_DIV2;
/* APB4 = AHB / 2 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV2;
/* APB3 = AHB / 2 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV2;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 2 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV2;
/* PLL0 select HXTAL, configure PLL0 input and output range */
RCU_PLLALL &= ~(RCU_PLLALL_PLLSEL | RCU_PLLALL_PLL0VCOSEL | RCU_PLLALL_PLL0RNG);
RCU_PLLALL |= (RCU_PLLSRC_HXTAL | RCU_PLLALL_PLL0VCOSEL | RCU_PLL0RNG_4M_8M);
/* PLL0P = HXTAL / 5 * 80 = 400 MHz */
RCU_PLL0 &= ~(RCU_PLL0_PLL0N | RCU_PLL0_PLL0PSC | RCU_PLL0_PLL0P | RCU_PLL0_PLL0R | RCU_PLL0_PLLSTBSRC);
RCU_PLL0 |= ((PLL0N << PLL0N_REG_OFFSET) | (PLL0PSC << PLL0PSC_REG_OFFSET) | (PLL0P << PLL0P_REG_OFFSET) | (PLL0R << PLL0R_REG_OFFSET));
RCU_PLLADDCTL &= ~(RCU_PLLADDCTL_PLL0Q);
RCU_PLLADDCTL |= (PLL0Q << PLL0Q_REG_OFFSET);
/* enable PLL0P, PLL0Q, PLL0R */
RCU_PLLADDCTL |= RCU_PLLADDCTL_PLL0PEN | RCU_PLLADDCTL_PLL0QEN | RCU_PLLADDCTL_PLL0REN;
/* enable PLL */
RCU_CTL |= RCU_CTL_PLL0EN;
/* wait until PLL0 is stable */
while(0U == (RCU_CTL & RCU_CTL_PLL0STB)) {
}
/* select PLL0 as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_PLL0P;
/* wait until PLL0 is selected as system clock */
while(RCU_SCSS_PLL0P != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_480M_PLL0_HXTAL)
/*!
\brief configure the system clock to 480M by PLL0 which selects HXTAL as its clock source
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_480m_hxtal(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable HXTAL */
RCU_CTL |= RCU_CTL_HXTALEN;
/* wait until HXTAL is stable or the startup time is longer than HXTAL_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_HXTALSTB);
} while((0U == stab_flag) && (HXTAL_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_HXTALSTB)) {
while(1) {
}
}
/* insert TCM wait state at 480MHz */
RCU_APB4EN |= RCU_APB4EN_SYSCFG;
SYSCFG_SRAMCFG1 |= SYSCFG_SRAMCFG1_TCM_WAITSTATE;
/* HXTAL is stable */
/* AHB = SYSCLK / 2 */
RCU_CFG0 |= RCU_AHB_CKSYS_DIV2;
/* APB4 = AHB / 2 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV2;
/* APB3 = AHB / 2 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV2;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 2 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV2;
/* PLL select HXTAL, configure PLL input and output range */
RCU_PLLALL &= ~(RCU_PLLALL_PLLSEL | RCU_PLLALL_PLL0VCOSEL | RCU_PLLALL_PLL0RNG);
RCU_PLLALL |= (RCU_PLLSRC_HXTAL | RCU_PLL0RNG_4M_8M);
/* PLL0P = HXTAL / 5 * 96 = 480 MHz */
RCU_PLL0 &= ~(RCU_PLL0_PLL0N | RCU_PLL0_PLL0PSC | RCU_PLL0_PLL0P | RCU_PLL0_PLL0R | RCU_PLL0_PLLSTBSRC);
RCU_PLL0 |= ((PLL0N << PLL0N_REG_OFFSET) | (PLL0PSC << PLL0PSC_REG_OFFSET) | (PLL0P << PLL0P_REG_OFFSET) | (PLL0R << PLL0R_REG_OFFSET));
RCU_PLLADDCTL &= ~(RCU_PLLADDCTL_PLL0Q);
RCU_PLLADDCTL |= (PLL0Q << PLL0Q_REG_OFFSET);
/* enable PLL0P, PLL0Q, PLL0R */
RCU_PLLADDCTL |= RCU_PLLADDCTL_PLL0PEN | RCU_PLLADDCTL_PLL0QEN | RCU_PLLADDCTL_PLL0REN;
/* enable PLL0 */
RCU_CTL |= RCU_CTL_PLL0EN;
/* wait until PLL0 is stable */
while(0U == (RCU_CTL & RCU_CTL_PLL0STB)) {
}
/* select PLL0 as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_PLL0P;
/* wait until PLL0 is selected as system clock */
while(RCU_SCSS_PLL0P != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#elif defined (__SYSTEM_CLOCK_600M_PLL0_HXTAL)
/*!
\brief configure the system clock to 600M by PLL0 which selects HXTAL as its clock source
\param[in] none
\param[out] none
\retval none
*/
static void system_clock_600m_hxtal(void)
{
uint32_t timeout = 0U;
uint32_t stab_flag = 0U;
/* enable HXTAL */
RCU_CTL |= RCU_CTL_HXTALEN;
/* wait until HXTAL is stable or the startup time is longer than HXTAL_STARTUP_TIMEOUT */
do {
timeout++;
stab_flag = (RCU_CTL & RCU_CTL_HXTALSTB);
} while((0U == stab_flag) && (HXTAL_STARTUP_TIMEOUT != timeout));
/* if fail */
if(0U == (RCU_CTL & RCU_CTL_HXTALSTB)) {
while(1) {
}
}
/* insert TCM wait state at 600MHz */
RCU_APB4EN |= RCU_APB4EN_SYSCFG;
SYSCFG_SRAMCFG1 |= SYSCFG_SRAMCFG1_TCM_WAITSTATE;
/* HXTAL is stable */
/* AHB = SYSCLK / 2 */
RCU_CFG0 |= RCU_AHB_CKSYS_DIV2;
/* APB4 = AHB / 2 */
RCU_CFG0 |= RCU_APB4_CKAHB_DIV2;
/* APB3 = AHB / 2 */
RCU_CFG0 |= RCU_APB3_CKAHB_DIV2;
/* APB2 = AHB / 1 */
RCU_CFG0 |= RCU_APB2_CKAHB_DIV1;
/* APB1 = AHB / 2 */
RCU_CFG0 |= RCU_APB1_CKAHB_DIV2;
/* PLL select HXTAL, configure PLL input and output range */
RCU_PLLALL &= ~(RCU_PLLALL_PLLSEL | RCU_PLLALL_PLL0VCOSEL | RCU_PLLALL_PLL0RNG);
RCU_PLLALL |= (RCU_PLLSRC_HXTAL | RCU_PLL0RNG_4M_8M);
/* PLL0P = HXTAL / 5 * 120 = 600 MHz */
RCU_PLL0 &= ~(RCU_PLL0_PLL0N | RCU_PLL0_PLL0PSC | RCU_PLL0_PLL0P | RCU_PLL0_PLL0R | RCU_PLL0_PLLSTBSRC);
RCU_PLL0 |= ((PLL0N << PLL0N_REG_OFFSET) | (PLL0PSC << PLL0PSC_REG_OFFSET) | (PLL0P << PLL0P_REG_OFFSET) | (PLL0R << PLL0R_REG_OFFSET));
RCU_PLLADDCTL &= ~(RCU_PLLADDCTL_PLL0Q);
RCU_PLLADDCTL |= (PLL0Q << PLL0Q_REG_OFFSET);
/* enable PLL0P, PLL0Q, PLL0R */
RCU_PLLADDCTL |= RCU_PLLADDCTL_PLL0PEN | RCU_PLLADDCTL_PLL0QEN | RCU_PLLADDCTL_PLL0REN;
/* enable PLL0 */
RCU_CTL |= RCU_CTL_PLL0EN;
/* wait until PLL0 is stable */
while(0U == (RCU_CTL & RCU_CTL_PLL0STB)) {
}
/* select PLL0 as system clock */
RCU_CFG0 &= ~RCU_CFG0_SCS;
RCU_CFG0 |= RCU_CKSYSSRC_PLL0P;
/* wait until PLL0 is selected as system clock */
while(RCU_SCSS_PLL0P != (RCU_CFG0 & RCU_CFG0_SCSS)) {
}
}
#endif /* __SYSTEM_CLOCK_IRC64M */
/*!
\brief update the SystemCoreClock with current core clock retrieved from cpu registers
\param[in] none
\param[out] none
\retval none
*/
void SystemCoreClockUpdate(void)
{
uint32_t sws = 0U;
uint32_t irc64div = 0U;
uint32_t pllpsc = 0U, plln = 0U, pllp = 0U, pllsel = 0U;
sws = GET_BITS(RCU_CFG0, 2, 3);
switch(sws) {
/* IRC64M is selected as CK_SYS */
case SEL_IRC64MDIV:
irc64div = (1U << GET_BITS(RCU_ADDCTL1, 16, 17));
SystemCoreClock = IRC64M_VALUE / irc64div;
break;
/* HXTAL is selected as CK_SYS */
case SEL_LPIRC4M:
SystemCoreClock = LPIRC4M_VALUE;
break;
/* HXTAL is selected as CK_SYS */
case SEL_HXTAL:
SystemCoreClock = HXTAL_VALUE;
break;
/* PLL0P is selected as CK_SYS */
case SEL_PLL0P:
/* get the value of PLL0PSC[0,5], PLL0N[6,14], PLL0P[16,22] */
pllpsc = GET_BITS(RCU_PLL0, 0, 5);
plln = GET_BITS(RCU_PLL0, 6, 14) + 1U;
pllp = GET_BITS(RCU_PLL0, 16, 22) + 1U;
/* PLL clock source selection, HXTAL or IRC64M_VALUE or LPIRC4M_VALUE */
pllsel = GET_BITS(RCU_PLLALL, 16, 17);
if(0U == pllsel) {
irc64div = (1U << GET_BITS(RCU_ADDCTL1, 16, 17));
SystemCoreClock = (IRC64M_VALUE / irc64div / pllpsc) * plln / pllp;
} else if(1U == pllsel) {
SystemCoreClock = (LPIRC4M_VALUE / pllpsc) * plln / pllp;
} else {
SystemCoreClock = (HXTAL_VALUE / pllpsc) * plln / pllp;
}
break;
default:
/* should not be here */
break;
}
}
#ifdef __FIRMWARE_VERSION_DEFINE
/*!
\brief get firmware version
\param[in] none
\param[out] none
\retval firmware version
*/
uint32_t gd32h7xx_firmware_version_get(void)
{
return __GD32H7XX_STDPERIPH_VERSION;
}
#endif /* __FIRMWARE_VERSION_DEFINE */